[Paraview] Probe : temporal curve

[Thierry Dubuis]

Hello David,

Thank you very much for your email.
I have tested the temporal probe with VTK, VTU files, it's Ok.
I will make other tests but only in september now.

Now just a suggestion for your sagacity : Is it possible to separate
temporal curve and animation ? (for the computation time)
   for exemple : I try to make a temporal curve under 65 vtk files, I was
waiting for more than 5 minutes.

And for information : How the time (X) of the temporal curve are computed ?
first =0, second=1,... ?

Congratulation to the Paraview team !!!

Thanks again,
-----------------------------------------------------
Thierry Dubuis
Sciences & Computer Consultants
Tel Dir  : 04 77 49 75 84
Tel Std : 04 77 49 75 80
----- Original Message -----
From: "David E DeMarle" <dave.demarle at kitware.com>
To: "Thierry Dubuis" <tdubuis at scconsultants.com>
Cc: <paraview at paraview.org>
Sent: Monday, July 25, 2005 3:30 PM
Subject: Re: [Paraview] Probe : temporal curve


> Hello list,
>
> The first draft of the Temporal Probe is now in the CVS development
> version. Go ahead an give it a try please. To use it, insert and place a
> point probe as normal. Next, enable the XY plot for the point probe. Use
> the play button on the animation control area to run through the time
> steps. The gathered data at that point will show up in the plot as the
> animation progresses.
>
> cheers,
> Dave DeMarle
>
>
> Thierry Dubuis wrote:
>
> >Hello David,
> >
> >Could you please send me an email when this functionnality is ready in
CVS ?
> >
> >Thank you very much
> >
> >Best regards
> >-----------------------------------------------------
> >Thierry Dubuis
> >Sciences & Computer Consultants
> >Tel Dir  : 04 77 49 75 84
> >Tel Std : 04 77 49 75 80
> >----- Original Message -----
> >From: "David E DeMarle" <dave.demarle at kitware.com>
> >To: "Thierry Dubuis" <tdubuis at scconsultants.com>
> >Cc: <paraview at paraview.org>
> >Sent: Thursday, July 07, 2005 3:45 PM
> >Subject: Re: [Paraview] Probe : temporal curve
> >
> >
> >
> >
> >>I'm working on that currently. I should have that in cvs HEAD and ready
> >>to test within the next couple of days.
> >>
> >>Dave DeMarle
> >>
> >>Thierry Dubuis wrote:
> >>
> >>
> >>
> >>>Hello,
> >>>
> >>>Again a question about the probes.
> >>>
> >>>I have a simulation tool which give a set of VTK files, 1 VTK file is
> >>>a time increment.
> >>>In thus condition, can I build curve in function of time in Paraview ?
> >>>
> >>>Best regards,
> >>>-----------------------------------------------------
> >>>Thierry Dubuis
> >>>Sciences & Computer Consultants
> >>>Tel Dir  : 04 77 49 75 84
> >>>Tel Std : 04 77 49 75 80
> >>>
>
>>>------------------------------------------------------------------------
> >>>
> >>>_______________________________________________
> >>>ParaView mailing list
> >>>ParaView at paraview.org
> >>>http://www.paraview.org/mailman/listinfo/paraview
> >>>
> >>>
> >>>
> >>>
> >
> >
> >
> >
> >
>
>