[vtkusers] [Paraview] paraview won't read plot3D files

[da]

Can you attach an example file that paraview reads differently compared to
Tecplot?

On Wed, Mar 17, 2010 at 4:54 PM, Rick Burnes <rick.burnes at mchsi.com> wrote:

> Yes, I have also generated an ASCII plot3D file, which I can get paraview
> to read.  However, paraview does not correctly interpret the grid file.  The
> geometry I create with my simple Fortran code is a cube.  Paraview
> successfully reads both the ASCII grid and data files, but when I view it in
> paraview the geometry is incorrect.  Tecplot does not have this problem with
> the same grid and data files.  I am interested in any suggestions on the
> right combination of options to choose when reading this plot3D file into
> paraview, but I have not been able to find the correct combination of
> options to read a plot3D binary grid and data file.  In addition, since
> paraview does not display the correct geometry when I have it read an ASCII
> version of the same grid and data plot3D files I believe there is more to
> this than just choosing the right options.
>
> There are a number of different plot3D formats and I have tried reading a
> number of these into paraview, all with the same results.
>
> Sincerely,
> Rick
>
>
> On Mar 17, 2010, at 4:26 PM, da wrote:
>
> Have you tried generating an ascii file from Fortran and looking at it? I
> don't believe there should be a difference whether its generated from
> Fortran or C/C++ code.
>
> Tecplot's reader automatically detects the options of the plot3d file -
> while Paraview does not: its most likely the case that an option is set
> incorrectly.
>
> On Wed, Mar 17, 2010 at 3:29 PM, Rick Burnes <rick.burnes at mchsi.com>wrote:
>
>> Paraview appears to have a limited ability certain plot3D files that were
>> likely generated from C/C++ code, but is unable to read plot3D files
>> generated from Fortran code.  When I open a Fortran generated plot3D file I
>> select "plot3D" as the file type and then select the following three
>> options: "binary file", "has byte count" and if needed "multigrid".  I have
>> tried various combinations of these options without success.  I wrote a
>> short and simple Fortran program to generate a small test plot3D grid file
>> and data file, which I can successfully read with tecplot, but is not
>> readable in paraview 3.6.1.  Has anyone had success reading Fortran
>> generated plot3D files with a recent version of paraview and if so, what
>> plot3D format was used and what paraview file options were selected?
>>
>> This is for paraview 3.6.1 on a mac running leopard.  However, I run into
>> the same problem on the windows version of paraview as well.
>>
>> Here is the error message I receive:
>>
>> ERROR: In
>> /Users/kitware/ParaViewReleases/ParaView-3.6/ParaView3/VTK/IO/vtkMultiBlockPLOT3DReader.cxx,
>> line 783
>> vtkMultiBlockPLOT3DReader (0x223c4620): Error reading geometry file.
>>
>>
>> ERROR: In
>> /Users/kitware/ParaViewReleases/ParaView-3.6/ParaView3/VTK/Filtering/vtkExecutive.cxx,
>> line 757
>> vtkCompositeDataPipeline (0x223c4590): Algorithm
>> vtkMultiBlockPLOT3DReader(0x223c4620) returned failure for request:
>> vtkInformation (0x2245e940)
>>  Debug: Off
>>  Modified Time: 79689
>>  Reference Count: 1
>>  Registered Events: (none)
>>  Request: REQUEST_DATA
>>  FORWARD_DIRECTION: 0
>>  ALGORITHM_AFTER_FORWARD: 1
>>  FROM_OUTPUT_PORT: 0
>>
>> Also, are there any plans to improve paraview's ability to read plot3D
>> files?
>>
>> Sincerely,
>> Rick
>> _______________________________________________
>> Powered by www.kitware.com
>>
>> Visit other Kitware open-source projects at
>> http://www.kitware.com/opensource/opensource.html
>>
>> Please keep messages on-topic and check the ParaView Wiki at:
>> http://paraview.org/Wiki/ParaView
>>
>> Follow this link to subscribe/unsubscribe:
>> http://www.paraview.org/mailman/listinfo/paraview
>>
>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.vtk.org/pipermail/vtkusers/attachments/20100317/24511ccb/attachment.htm>