[Paraview] [Non-DoD Source] Re: Superbuild repo change?

Tue Feb 21 11:31:58 EST 2017

I did a “git pull” and “git submodule update” in the paraview-superbuild
directory.   I then changed the source flag in my cmake command:

-Dparaview_SOURCE_SELECTION="5.3.0-RC1”

and I get this error when doing a clean build.

-- Detecting CXX compile features - done
-- Check size of void*
-- Check size of void* - done
CMake Error at superbuild/cmake/SuperbuildRevisionMacros.cmake:338
(message):
  The 5.3.0-RC1 source selection for paraview does not exist.
Call Stack (most recent call first):
  versions.cmake:62 (superbuild_set_selectable_source)
  superbuild/CMakeLists.txt:96 (include)

I grepp’ed through the paraview-superbuild directory and I don’t see any
references to 5.3.

________________________________
Rick Angelini
USArmy Research Laboratory
CISD/HPC Architectures Team
Phone:  410-278-6266

-----Original Message-----
From: Cory Quammen <cory.quammen at kitware.com>
Date: Tuesday, February 21, 2017 at 10:07 AM
To: Rick Angelini <Richard.C.Angelini.CIV at mail.mil>
Cc: "ben.boeckel at kitware.com" <ben.boeckel at kitware.com>, ParaView
<paraview at paraview.org>
Subject: Re: [Paraview] [Non-DoD Source] Re: Superbuild repo change?

All active links contained in this email were disabled.  Please verify the
identity of the sender, and confirm the authenticity of all links
contained within the message prior to copying and pasting the address to a
Web browser.  

----

Hi Rick,

>From paraview-superbuild master (remember to run 'git submodule
update' after updating master), you should be able to set
paraview_SOURCE_SELECTION to 5.3.0-RC1. Then just configure and build.

These directions are distilled from the README.md file in the
superbuild directory [1]. Relevant excerpt:

"3. Another option is to use a source tarball of a ParaView release.
For that, set paraview_SOURCE_SELECTION to the version to build such
as 5.2.0. The superbuild offers the lastest stable release as well as
release candidate in preparation for the release. This is the best way
to build a released version of ParaView."

For each release candidate and release, we add an entry under
paraview_SOURCE_SELECTION that you can select.

Let us know if you run into problems.

Thanks,
Cory

[1] 
Caution-https://gitlab.kitware.com/paraview/paraview-superbuild/blob/master
/README.md

On Tue, Feb 21, 2017 at 8:42 AM, Angelini, Richard C (Rick) CIV USARMY
RDECOM ARL (US) <richard.c.angelini.civ at mail.mil> wrote:
> What are the instructions for using PVSB to build the 5.3- RC ?
> ________________________________
> Rick Angelini
> USArmy Research Laboratory
> CISD/HPC Architectures Team
> Phone:  410-278-6266
>
>
>
>
> -----Original Message-----
> From: Ben Boeckel <ben.boeckel at kitware.com>
> Reply-To: "ben.boeckel at kitware.com" <ben.boeckel at kitware.com>
> Date: Wednesday, February 15, 2017 at 11:34 AM
> To: Rick Angelini <Richard.C.Angelini.CIV at mail.mil>
> Cc: ParaView <paraview at paraview.org>
> Subject: [Non-DoD Source] Re: [Paraview] Superbuild repo change?
>
> On Wed, Feb 15, 2017 at 13:50:13 +0000, Angelini, Richard C (Rick) CIV
> USARMY RDECOM ARL (US) wrote:
>> I did a fresh pull of the ParaView superbuild repository, and now I
>>can’t do
>> a clean build of PV 5.2.0 on my Mac (OSX 10.9.5).
>>
>> First, I had to remove the entries for “qt” and “scipy" in the
>> CMakeLists.txt:
>
> You need to run `git submodule update` to update the common-superbuild
> bits.
>
>> After removing those entries, the cmake completes and the build starts
>>and
>> passes out in qt4.
>> I’m not sure why it’s complaining about OS X 10.7 or later?)
>
> What version of Xcode are you using?
>
> --Ben
>
> _______________________________________________
> Powered by Caution-www.kitware.com
>
> Visit other Kitware open-source projects at
>Caution-http://www.kitware.com/opensource/opensource.html
>
> Please keep messages on-topic and check the ParaView Wiki at:
>Caution-http://paraview.org/Wiki/ParaView
>
> Search the list archives at:
>Caution-http://markmail.org/search/?q=ParaView
>
> Follow this link to subscribe/unsubscribe:
> Caution-http://public.kitware.com/mailman/listinfo/paraview
>

-- 
Cory Quammen
Staff R&D Engineer
Kitware, Inc.
-------------- next part --------------
A non-text attachment was scrubbed...
Name: smime.p7s
Type: application/pkcs7-signature
Size: 5108 bytes
Desc: not available
URL: <http://public.kitware.com/pipermail/paraview/attachments/20170221/f09b7e8d/attachment.bin>