[Paraview] Installing paraviewweb on a raspberry pi

[Faiz Abidi]

Hi Faraz,

I can look into your system if you can provide me ssh access. I don't
promise to fix your issue but have experience with Raspberry Pis and
Paraview builds. And I don't need money, I'll do it out of curiosity and in
free time :)

On Tue, Feb 14, 2017 at 4:55 PM, Faraz Hussain <info at feacluster.com> wrote:

> Unfortunately, I am not having much luck getting Paraview to build. I keep
> trying to configure (c), but the generate (g) option does not come. I am
> wondering if someone would be willing to poke around in my system . I can
> pay some nominal amount for your time. However , since this is mainly for
> education my budget is limited ( ~$100 ).
>
>
> Quoting Sebastien Jourdain <sebastien.jourdain at kitware.com>:
>
> You need to hit [c](configure) several time before getting the generate.
>>
>> On Fri, Feb 10, 2017 at 2:33 PM, Scott Wittenburg <
>> scott.wittenburg at kitware.com> wrote:
>>
>> Also for paraviewweb, don't forget:
>>>
>>> PARAVIEW_ENABLE_PYTHON=ON
>>>
>>> Cheers,
>>>
>>> Scott
>>>
>>> On Fri, Feb 10, 2017 at 2:31 PM, Scott Wittenburg <
>>> scott.wittenburg at kitware.com> wrote:
>>>
>>> I would think you'd want to build with:
>>>>
>>>> PARAVIEW_BUILD_QT_GUI=OFF
>>>>
>>>> Hope this helps,
>>>>
>>>> Scott
>>>>
>>>> On Fri, Feb 10, 2017 at 2:25 PM, Faraz Hussain <info at feacluster.com>
>>>> wrote:
>>>>
>>>> Thanks for your help in installing Paraview on a raspberry pi. I
>>>>> followed the steps in:
>>>>>
>>>>> http://www.paraview.org/Wiki/ParaView:Build_And_Install
>>>>>
>>>>> However, when I configure ccmake it says QT is needed. I could not
>>>>> figure out if I can ignore that. The "generate" command did not come
>>>>> up.
>>>>>
>>>>> On a side note, it took me a while to find ccmake. I thought it was
>>>>> installed with cmake, but seems I had to install it separately using
>>>>> "sudo
>>>>> apt-get install cmake-curses-gui" . Perhaps the instructions should be
>>>>> updated to reflect this to avoid confusion.
>>>>>
>>>>>
>>>>> Quoting Sebastien Jourdain <sebastien.jourdain at kitware.com>:
>>>>>
>>>>> Wow,
>>>>>
>>>>>>
>>>>>> I'm not an expert on raspberry pi but it should be possible.
>>>>>> BUT, (and it is a big but) you need some graphics capability for
>>>>>> ParaView
>>>>>> or good CPUs if you don't have a GPU.
>>>>>> Or the rendering will be really slow.
>>>>>>
>>>>>> The quicker test you can do, is to build ParaView (without Qt) and try
>>>>>> to
>>>>>> run Visualizer with that ParaView in the command line to see what
>>>>>> performance you are getting. If that's reasonable, then all the
>>>>>> network
>>>>>> setup should be "trivial".
>>>>>>
>>>>>> ParaView: http://www.paraview.org/Wiki/ParaView:Build_And_Install
>>>>>> Visualizer: https://kitware.github.io/visualizer/
>>>>>>
>>>>>> Good luck,
>>>>>>
>>>>>> Seb
>>>>>>
>>>>>> On Wed, Feb 8, 2017 at 8:15 AM, Faraz Hussain <info at feacluster.com>
>>>>>> wrote:
>>>>>>
>>>>>> I want to be able to manipulate vtk file on my raspberry pi via a web
>>>>>>
>>>>>>> browser anywhere in the world. I believe I need to install
>>>>>>> paraviewweb
>>>>>>> and
>>>>>>> do some reconfiguration of apache and the virtual hosts?
>>>>>>> Unfortunately, I
>>>>>>> am not a guru of Linux. So before I attempt it all, is it even
>>>>>>> possible to
>>>>>>> do this on a raspberry pi? I am using raspian .
>>>>>>>
>>>>>>> _______________________________________________
>>>>>>> Powered by www.kitware.com
>>>>>>>
>>>>>>> Visit other Kitware open-source projects at
>>>>>>> http://www.kitware.com/opensou
>>>>>>> rce/opensource.html
>>>>>>>
>>>>>>> Please keep messages on-topic and check the ParaView Wiki at:
>>>>>>> http://paraview.org/Wiki/ParaView
>>>>>>>
>>>>>>> Search the list archives at: http://markmail.org/search/?q=ParaView
>>>>>>>
>>>>>>> Follow this link to subscribe/unsubscribe:
>>>>>>> http://public.kitware.com/mailman/listinfo/paraview
>>>>>>>
>>>>>>>
>>>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> Powered by www.kitware.com
>>>>>
>>>>> Visit other Kitware open-source projects at
>>>>> http://www.kitware.com/opensource/opensource.html
>>>>>
>>>>> Please keep messages on-topic and check the ParaView Wiki at:
>>>>> http://paraview.org/Wiki/ParaView
>>>>>
>>>>> Search the list archives at: http://markmail.org/search/?q=ParaView
>>>>>
>>>>> Follow this link to subscribe/unsubscribe:
>>>>> http://public.kitware.com/mailman/listinfo/paraview
>>>>>
>>>>>
>>>>
>>>>
>>>
>
>
> _______________________________________________
> Powered by www.kitware.com
>
> Visit other Kitware open-source projects at http://www.kitware.com/opensou
> rce/opensource.html
>
> Please keep messages on-topic and check the ParaView Wiki at:
> http://paraview.org/Wiki/ParaView
>
> Search the list archives at: http://markmail.org/search/?q=ParaView
>
> Follow this link to subscribe/unsubscribe:
> http://public.kitware.com/mailman/listinfo/paraview
>



-- 
Faiz Abidi | Master's Student at Virginia Tech | www.faizabidi.com |
+1-540-998-6636
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://public.kitware.com/pipermail/paraview/attachments/20170214/712d7688/attachment.html>