[Paraview] Installing paraviewweb on a raspberry pi

[Scott Wittenburg]

Also for paraviewweb, don't forget:

PARAVIEW_ENABLE_PYTHON=ON

Cheers,

Scott

On Fri, Feb 10, 2017 at 2:31 PM, Scott Wittenburg <
scott.wittenburg at kitware.com> wrote:

> I would think you'd want to build with:
>
> PARAVIEW_BUILD_QT_GUI=OFF
>
> Hope this helps,
>
> Scott
>
> On Fri, Feb 10, 2017 at 2:25 PM, Faraz Hussain <info at feacluster.com>
> wrote:
>
>> Thanks for your help in installing Paraview on a raspberry pi. I followed
>> the steps in:
>>
>> http://www.paraview.org/Wiki/ParaView:Build_And_Install
>>
>> However, when I configure ccmake it says QT is needed. I could not figure
>> out if I can ignore that. The "generate" command did not come up.
>>
>> On a side note, it took me a while to find ccmake. I thought it was
>> installed with cmake, but seems I had to install it separately using "sudo
>> apt-get install cmake-curses-gui" . Perhaps the instructions should be
>> updated to reflect this to avoid confusion.
>>
>>
>> Quoting Sebastien Jourdain <sebastien.jourdain at kitware.com>:
>>
>> Wow,
>>>
>>> I'm not an expert on raspberry pi but it should be possible.
>>> BUT, (and it is a big but) you need some graphics capability for ParaView
>>> or good CPUs if you don't have a GPU.
>>> Or the rendering will be really slow.
>>>
>>> The quicker test you can do, is to build ParaView (without Qt) and try to
>>> run Visualizer with that ParaView in the command line to see what
>>> performance you are getting. If that's reasonable, then all the network
>>> setup should be "trivial".
>>>
>>> ParaView: http://www.paraview.org/Wiki/ParaView:Build_And_Install
>>> Visualizer: https://kitware.github.io/visualizer/
>>>
>>> Good luck,
>>>
>>> Seb
>>>
>>> On Wed, Feb 8, 2017 at 8:15 AM, Faraz Hussain <info at feacluster.com>
>>> wrote:
>>>
>>> I want to be able to manipulate vtk file on my raspberry pi via a web
>>>> browser anywhere in the world. I believe I need to install paraviewweb
>>>> and
>>>> do some reconfiguration of apache and the virtual hosts? Unfortunately,
>>>> I
>>>> am not a guru of Linux. So before I attempt it all, is it even possible
>>>> to
>>>> do this on a raspberry pi? I am using raspian .
>>>>
>>>> _______________________________________________
>>>> Powered by www.kitware.com
>>>>
>>>> Visit other Kitware open-source projects at
>>>> http://www.kitware.com/opensou
>>>> rce/opensource.html
>>>>
>>>> Please keep messages on-topic and check the ParaView Wiki at:
>>>> http://paraview.org/Wiki/ParaView
>>>>
>>>> Search the list archives at: http://markmail.org/search/?q=ParaView
>>>>
>>>> Follow this link to subscribe/unsubscribe:
>>>> http://public.kitware.com/mailman/listinfo/paraview
>>>>
>>>>
>>
>>
>> _______________________________________________
>> Powered by www.kitware.com
>>
>> Visit other Kitware open-source projects at
>> http://www.kitware.com/opensource/opensource.html
>>
>> Please keep messages on-topic and check the ParaView Wiki at:
>> http://paraview.org/Wiki/ParaView
>>
>> Search the list archives at: http://markmail.org/search/?q=ParaView
>>
>> Follow this link to subscribe/unsubscribe:
>> http://public.kitware.com/mailman/listinfo/paraview
>>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://public.kitware.com/pipermail/paraview/attachments/20170210/7905aa5d/attachment.html>