[Fwd: RE: [Paraview] Getting started]

Fri Aug 18 11:08:27 EDT 2006

Attached is some further diagnostic information for the problem
described below. Thanks.

Tom 

-----Original Message-----
From: paraview-bounces+thomas.chyczewski=ngc.com at paraview.org
[mailto:paraview-bounces+thomas.chyczewski=ngc.com at paraview.org] On
Behalf Of Berk Geveci
Sent: Friday, August 18, 2006 9:34 AM
To: ParaView Mailing List
Subject: [Fwd: RE: [Paraview] Getting started]

I was able to get the files with names truncated by tar from the zipped
distribution file. The execution of ccmake was successful. When I tried
to compile with "make && make install" I immediately get

no arguments or description file (bu7).
*** Error code 1 (bu21)
*** Error code 1 (bu21)
*** Error code 1 (bu21)

The installation instructions point out that gmake may be needed. Is
that what you conclude from the error message I received?

Tom

---------------------------------------
Dr. Thomas S. Chyczewski, M/S U01-026
Technology Development
Northrop Grumman Corporation
925 South Oyster Bay Road
Bethpage, NY 11714-3582

Tel: (516) 704-3667
Fax: (516) 346-8130
-----Original Message-----
From: Berk Geveci [mailto:berk.geveci at kitware.com]
Sent: Thursday, August 17, 2006 2:38 PM
To: Chyczewski, Thomas
Subject: Re: [Paraview] Getting started

Hi Tom,

I checked and the archive is intact. It sounds like there is a length
limitation for filenames on your system. Can you verify if this is the
case?

-Berk

Chyczewski, Thomas wrote:
>  
> (Berk, I sent this yesterday but suspect it did not make it through)
>  
> Yes. The SimpleWindowWithImageWidget directory contains only
>  
> CmakeLists.txt
> KWSimpleWindowWithImageWidgetEx
> vtkKWSimpleWindowWithImageWidge
>  
> Tom
>  
> 
> ---------------------------------------
> Dr. Thomas S. Chyczewski, M/S U01-026
> Technology Development
> Northrop Grumman Corporation
> 925 South Oyster Bay Road
> Bethpage, NY 11714-3582
> 
> Tel: (516) 704-3667
> Fax: (516) 346-8130
> 
>  
> 
> ----------------------------------------------------------------------
> --
> *From:* Berk Geveci [mailto:berk.geveci at gmail.com]
> *Sent:* Tuesday, August 15, 2006 4:56 PM
> *To:* Chyczewski, Thomas
> *Subject:* Re: [Paraview] Getting started
> 
> That's weird. I have that file in my cvs checkout. Can you check if 
> that directory is there?
> 
> 
> On 8/15/06, *Chyczewski, Thomas* < Thomas.Chyczewski at ngc.com 
> <mailto:Thomas.Chyczewski at ngc.com>> wrote:
> 
>     Berk,
>      
>     Please see attached. To be sure I am not omitting any steps in the
>     description of my problem, after I enter the ccmake command and
the
>     ccmake screen appears, I enter 'c' to start configuring. (It
appears
>     as though I have the option of changing
>     "CMAKE_BACKWARDS_COMPATIBILITY" from 2.4, but I don't change 
> anything. )
>      
>     Thanks for your help.
>      
>     Tom
> 
>
------------------------------------------------------------------------
>     *From:* Berk Geveci [mailto:berk.geveci at gmail.com
>     <mailto:berk.geveci at gmail.com>]
>     *Sent:* Tuesday, August 15, 2006 3:18 PM
>     *To:* Chyczewski, Thomas
>     *Cc:* paraview at paraview.org <mailto:paraview at paraview.org>
>     *Subject:* Re: [Paraview] Getting started
> 
>     Can you post the exact errors you are getting as well as the
>     CMakeCache.txt from your build tree. If your message is rejected
>     because of it's size, don't worry. I will make sure it goes
through.
> 
>     -Berk
> 
>     On 8/15/06, *Chyczewski, Thomas* <Thomas.Chyczewski at ngc.com
>     <mailto:Thomas.Chyczewski at ngc.com>> wrote:
> 
> 
>         I would like to give Paraview a try but am having trouble
>         building an
>         executable. Is there an archive somewhere that contains more
>         information
>         than that given in Install link of paraview.org
>         <http://paraview.org>?
> 
>         In case someone on this list can help, here is my problem:
> 
>         I have an SGI running IRIX 6.5. I downloaded ccmake 2.4.3 and
>         paraview
>         2.4.4. I installed cmake, untarred paraview, created the
directory
>         ./paraview-2.4.4-irix, created the environmental variables
>         pointing to
>         my c and c++ compilers and executed "ccmake ../paraview-2.4.4"
>         in that
>         directory. After a little while, I get the error message
stating
>         that it
>         cannot find
>
paraview-2.4.4/GUI/Widgets/Examples/Cxx/SimpleWindowWithImageWidget/vtkK
>         WSimpleWindowWithImageWidgetExample.h plus 4 other files
similar
>         files.
>         As I doubt that I have uncovered an ommision in the
distribution
>         file, I
>         believe I am missing something. Can anyone help me out?
> 
>         I also tried to build paraview 2.2.1. In this case, I was able
>         to get
>         through ccmake, but the compilation failed because in
>         vtkThreadedController.h,  "pid_t" is undefined. Any
suggestions?
> 
>         Tom
>         _______________________________________________
>         ParaView mailing list
>         ParaView at paraview.org <mailto:ParaView at paraview.org>
>         http://www.paraview.org/mailman/listinfo/paraview
>         <http://www.paraview.org/mailman/listinfo/paraview>
> 
> 
> 
> 

_______________________________________________
ParaView mailing list
ParaView at paraview.org
http://www.paraview.org/mailman/listinfo/paraview
-------------- next part --------------
A non-text attachment was scrubbed...
Name: make.screenout
Type: application/octet-stream
Size: 418 bytes
Desc: make.screenout
Url : http://public.kitware.com/pipermail/paraview/attachments/20060818/014007e0/make-0001.obj
-------------- next part --------------
A non-text attachment was scrubbed...
Name: Makefile
Type: application/octet-stream
Size: 65700 bytes
Desc: Makefile
Url : http://public.kitware.com/pipermail/paraview/attachments/20060818/014007e0/Makefile-0001.obj