[Midas] Fwd: How to build ParaViewWeb with Slicer

[Sebastien Jourdain]

I guess the sample applications could be a good start. You can look in both
VTK and ParaView for that. Each of them contains several.

Seb


On Tue, Oct 22, 2013 at 10:33 AM, Ferdinando Primerano <
f.primerano90 at gmail.com> wrote:

> Can you please suggest me where I can start digging or where I can find
> the right documentation about the development part?
>
> Ferdinando
>
>
> 2013/10/22 Sebastien Jourdain <sebastien.jourdain at kitware.com>
>
>> Sure, you can start with that:
>> http://paraview.org/Wiki/ParaView:Build_And_Install
>>
>> But what you want to achieve is not something that is available directly.
>> You will need some small development on your end.
>>
>> Seb
>>
>>
>> On Tue, Oct 22, 2013 at 6:29 AM, Ferdinando Primerano <
>> f.primerano90 at gmail.com> wrote:
>>
>>> Hi Sebastien,
>>>
>>> Can you give me some guide to follow please?
>>> As I said I tried to setup an Apache front-end but it gives me an error
>>> during the compilation with 'make'.
>>> Supposing I can fix that somehow, how should I import only the slicer to
>>> my web page?
>>>
>>> Thank you again for your patience.
>>>
>>> Ferdinando
>>>
>>>
>>>
>>> 2013/10/21 Sebastien Jourdain <sebastien.jourdain at kitware.com>
>>>
>>>> Hi Ferdinando,
>>>>
>>>> If you want to achieve that on your end, you will definitely need to
>>>> build ParaView or VTK with the Python wrapping in order to enable the Web
>>>> support.
>>>> But after that, depending on your setup, you may need to setup an
>>>> Apache front-end to deal with the Websocket forwarding and some virtual
>>>> host to allow both your tomcat and our Session manager to respond within
>>>> the same domain.
>>>>
>>>> Seb
>>>>
>>>>
>>>> On Mon, Oct 21, 2013 at 2:31 PM, Ferdinando Primerano <
>>>> f.primerano90 at gmail.com> wrote:
>>>>
>>>>>
>>>>>
>>>>> ---------- Forwarded message ----------
>>>>> From: Ferdinando Primerano <f.primerano90 at gmail.com>
>>>>> Date: 2013/10/21
>>>>> Subject: How to build ParaViewWeb with Slicer
>>>>> To: midas at public.kitware.com
>>>>>
>>>>>
>>>>> Hi,
>>>>>
>>>>> I am new to ParaView and I am trying to use ParaViewWeb inside a
>>>>> website based on Apache Tomcat.
>>>>> In particular I would like to obtain this slicer:
>>>>> http://50.58.123.185/external/midas/visualize/paraview/slice?itemId=44
>>>>> and call it from my pages.
>>>>>
>>>>> I was searching through the internet about this but with no success.
>>>>> I tried to build ParaViewWeb as shown in this guide
>>>>> http://www.paraview.org/ParaView3/Doc/Nightly/www/js-doc/index.html#!/guide/apache_setup
>>>>> but I obtained an error while compiling with 'make' which gives
>>>>> problem with "all" and "default_target" after this point:
>>>>> [ 58%] Built target vtkEyeDomeLightingCS
>>>>>
>>>>> I'm not sure I'm doing the right thing for my goal, can you help me
>>>>> with this please?
>>>>>
>>>>> Thank you in advance.
>>>>>
>>>>> Best regards,
>>>>>
>>>>> Ferdinando
>>>>>
>>>>>
>>>>>
>>>>>
>>>>> _______________________________________________
>>>>> Midas mailing list
>>>>> Midas at public.kitware.com
>>>>> http://public.kitware.com/cgi-bin/mailman/listinfo/midas
>>>>>
>>>>>
>>>>
>>>
>>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://public.kitware.com/pipermail/midas/attachments/20131022/bd247f98/attachment.html>