[vtkusers] comparing data in two meshes that *nearly* match

[Bill Lorensen]

Take a look at this example:
http://vtk.org/Wiki/VTK/Examples/Cxx/PolyData/DistancePolyDataFilter




On Sat, May 18, 2013 at 8:22 AM, Marco Nawijn <nawijn at gmail.com> wrote:

> Hi Seth,
>
> Are you aware of the vtkProbeFilter? You could use the points of one
> mesh (the input mesh) and compute the value from the other mesh
> at the locations of the input mesh. See documentation string below.
>
> Regards,
>
> Marco
>
>
> Source: Python doc-string for vtkProbeFilter
>
> vtkProbeFilter is a filter that computes point attributes (e.g.,
> scalars, vectors, etc.) at specified point positions. The filter has
> two inputs: the Input and Source. The Input geometric structure is
> passed through the filter. The point attributes are computed at the
> Input point positions by interpolating into the source data. For
> example, we can compute data values on a plane (plane specified as
> Input) from a volume (Source). The cell data of the source data is
> copied to the output based on in which source cell each input point
> is. If an array of the same name exists both in source's point and
> cell data, only the one from the point data is probed.
>
> This filter can be used to resample data, or convert one dataset form
> into another. For example, an unstructured grid (vtkUnstructuredGrid)
> can be probed with a volume (three-dimensional vtkImageData), and
> then volume rendering techniques can be used to visualize the
> results. Another example: a line or curve can be used to probe data
> to produce x-y plots along that line or curve.
>
>
>
> On Fri, May 17, 2013 at 11:48 PM, Seth Gilchrist <seth at mech.ubc.ca> wrote:
>
>> Hello,
>> I'm trying to compare data on two meshes that are close to matching, but
>> don't quite match.
>>
>> The meshes are the surface of a bone with scalar data representing
>> physical strain observed at a given point. The bones were measured twice
>> under different conditions, and the two extracted surfaces are similar, but
>> not identical.
>>
>> I have used ICP to align the meshes, but can't figure out a way to
>> compare the data between the two meshes. One way would be to project the
>> data from each mesh onto a plane image, or better to warp one mesh to the
>> other and interpolate the data, but I can't figure that out either.
>>
>> So that you can see what I'm working with I've uploaded the meshes in vtp
>> format to
>> https://share.cfri.ca/?u=SN7q&p=9fAJ
>>
>> Any ideas would be much appreciated. I want to compare the strain in the
>> meshes on a point by point basis.
>>
>> Thanks for your time and ideas,
>> Seth
>>
>> _______________________________________________
>> Powered by www.kitware.com
>>
>> Visit other Kitware open-source projects at
>> http://www.kitware.com/opensource/opensource.html
>>
>> Please keep messages on-topic and check the VTK FAQ at:
>> http://www.vtk.org/Wiki/VTK_FAQ
>>
>> Follow this link to subscribe/unsubscribe:
>> http://www.vtk.org/mailman/listinfo/vtkusers
>>
>>
>
> _______________________________________________
> Powered by www.kitware.com
>
> Visit other Kitware open-source projects at
> http://www.kitware.com/opensource/opensource.html
>
> Please keep messages on-topic and check the VTK FAQ at:
> http://www.vtk.org/Wiki/VTK_FAQ
>
> Follow this link to subscribe/unsubscribe:
> http://www.vtk.org/mailman/listinfo/vtkusers
>
>


-- 
Unpaid intern in BillsBasement at noware dot com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.vtk.org/pipermail/vtkusers/attachments/20130518/7a12b62a/attachment.htm>