[Paraview] plume tracking-trajectory

Tue Jul 26 11:40:16 EDT 2016

I hope this time is ok 
the vtk file is the flow solution,the csv file is the particle data 

kostas 
----- Original Message -----

From: "Mathieu Westphal" <mathieu.westphal at kitware.com> 
To: "Konstantinos Panagiotou" <panagiotou.konstantinos at ucy.ac.cy> 
Cc: "ParaView" <paraview at paraview.org> 
Sent: Wednesday, July 27, 2016 12:24:04 AM 
Subject: Re: [Paraview] plume tracking-trajectory 

I am unable to load your pvsm. 
Please provide all the data needed by your pvsm in order for me to load it. 

Mathieu Westphal 

On Tue, Jul 26, 2016 at 5:03 PM, Konstantinos Panagiotou < panagiotou.konstantinos at ucy.ac.cy > wrote: 

hello 
i have loaded the csv data and a vtk file,a cube basicly, in which the flow solution is stored 

From: "Mathieu Westphal" < mathieu.westphal at kitware.com > 
To: "Konstantinos Panagiotou" < panagiotou.konstantinos at ucy.ac.cy > 
Cc: "ParaView" < paraview at paraview.org > 
Sent: Tuesday, July 26, 2016 11:53:41 PM 

Subject: Re: [Paraview] plume tracking-trajectory 

Your data does not seem to be correctly formated. 
Can you send me an associated pvsm file ? 

Mathieu Westphal 

On Tue, Jul 26, 2016 at 4:08 PM, Konstantinos Panagiotou < panagiotou.konstantinos at ucy.ac.cy > wrote: 

<blockquote>

Dear Mathieu, 
i have installed cmake and qt in order to use cmake command to convert to .vtp. However,i need to add some additional packages which i am not familiar with. 
So, instead of converting to .vtp, i am sending you in zip form two files with different formats, vtk and csv respectively, files which i have loaded to paraview and being able to animate them using glyph. they are few KB each, it is the minimum i could do in order to keep the example as simple as possible for possible extension later on. 
Sincerely, 
Kostas 

From: "Mathieu Westphal" < mathieu.westphal at kitware.com > 
To: "Konstantinos Panagiotou" < panagiotou.konstantinos at ucy.ac.cy >, "ParaView" < paraview at paraview.org > 
Sent: Tuesday, July 26, 2016 8:06:16 PM 

Subject: Re: [Paraview] plume tracking-trajectory 

Please keep the ml in the loop so everyone can follow this. 

Please open you csv data, save it as a .vtp file and send it to me (if it's not too big) 

Regards, 

Mathieu Westphal 

On Tue, Jul 26, 2016 at 12:55 PM, Konstantinos Panagiotou < panagiotou.konstantinos at ucy.ac.cy > wrote: 

<blockquote>

Hello Mathieu, 
i have applied the Temporal ParticlePath filter,however i havent seen any change. I mean, when i apply glyph to the input data, i can activate this filter and apply it to the input data,either vtk or csv point data. 
However, i havent managed yet to see trajectories of the particles, only the position of the particle or particles at a specific time step.I have searched and I have seen in other posts in the forum referring to the same issue, that the operation interface of the newest vesrion of paraview is different than the previous ones for the specific function. Can you guide me pls if you can? :) 

Thanks again, 
Kostas 

From: "Mathieu Westphal" < mathieu.westphal at kitware.com > 
To: "Konstantinos Panagiotou" < panagiotou.konstantinos at ucy.ac.cy > 
Cc: "ParaView" < paraview at paraview.org > 
Sent: Thursday, July 21, 2016 6:16:27 PM 
Subject: Re: [Paraview] plume tracking-trajectory 

Hello 

You should have a look to ParticlePath filter. 

Regards 

Mathieu Westphal 

On Thu, Jul 21, 2016 at 10:38 AM, Konstantinos Panagiotou < panagiotou.konstantinos at ucy.ac.cy > wrote: 

<blockquote>
Hi, 
i am having a problem on plotting the trajectory of a single particle at the top of a flow solution. Particularly, i have a csv file, which is named text0000.csv,inside which i have 4 columns, x,y,z, t.in addition, i have additional files text0001.csv,text0002.csv etc, with one row each( variables' values at each time step) 
When i load them to the paraview project,i have no problem on performing the animation.However, i also want to have particle's trajectory while it evolves, that is,having lines connecting the updated points with the previous ones. But i havent managed to do that yet. I have installed a paraview version 5.0.1. pls help me,what i should do? 
_______________________________________________ 
Powered by www.kitware.com 

Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html 

Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView 

Search the list archives at: http://markmail.org/search/?q=ParaView 

Follow this link to subscribe/unsubscribe: 
http://public.kitware.com/mailman/listinfo/paraview 

</blockquote>

</blockquote>

</blockquote>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://public.kitware.com/pipermail/paraview/attachments/20160726/0d9df92c/attachment-0001.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: vtk_test.vtk.zip
Type: application/zip
Size: 1586811 bytes
Desc: not available
URL: <http://public.kitware.com/pipermail/paraview/attachments/20160726/0d9df92c/attachment-0002.zip>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: csv_ag.zip
Type: application/zip
Size: 30725 bytes
Desc: not available
URL: <http://public.kitware.com/pipermail/paraview/attachments/20160726/0d9df92c/attachment-0003.zip>