[Paraview] issue with "make install" in 3.10

[Bastil2001 at yahoo.de]

David,

QtNetwork is not there, but it is there in my 3.8.1 installation....
After linking it I still get the same undefined smbol error.

Regards Bastian

You have /opt/paraview/3.10.0/lib/paraview-3.10/libQtXmlPatterns.so.4 in
your install tree. Is QtNetwork.so also in that directory?



Am 16.03.2011 19:29, schrieb Bastil2001 at yahoo.de:
> Robert, David,
>
> our QT 4.6.2 was build from source with QtNetwork enabled. So what is
> wrong?
>
> Regards Bastian
>
> Am 15.03.2011 22:04, schrieb Robert Maynard:
>> We are asking because the 4.6.X prebuilt frameworks from Nokia don't
>> come with QNetworkAccessManager. I would confirm with your
>> system administrator that Qt has been built with QtNetwork enabled.
>>
>>
>> On Tue, Mar 15, 2011 at 2:59 PM, Bastil2001 at yahoo.de
>> <mailto:Bastil2001 at yahoo.de> <Bastil2001 at yahoo.de
>> <mailto:Bastil2001 at yahoo.de>> wrote:
>>
>>     Am 14.03.2011 20:06, schrieb David Partyka:
>>>     Are you using a prebuilt qt from nokia? Or did you build it youself?
>>
>>     David,
>>
>>     our system administrator did the build. AFAIK it was build from
>>     source.
>>
>
>
>>     Regards Bastian
>>
>>
>>>
>>>     On Mon, Mar 14, 2011 at 3:01 PM, Bastil2001 at yahoo.de
>>>     <mailto:Bastil2001 at yahoo.de> <Bastil2001 at yahoo.de
>>>     <mailto:Bastil2001 at yahoo.de>> wrote:
>>>
>>>         Thanks David,
>>>
>>>         I forgot to mention - I already tried this. It does not help
>>>         at all. Instead of this I get three missing *.so-Libraries
>>>         (all from QT). After symmlinking them from the qt-lib to the
>>>         paraview-lib I still get the same error.
>>>
>>>         Regards Bastian
>>>
>>>         Am 14.03.2011 19:58, schrieb David Partyka:
>>>>         Try turning off PARAVIEW_INSTALL_THIRD_PARTY_LIBRARIES. ( I
>>>>         think I am going to make it default OFF instead of ON).
>>>>         Then blow away your install tree and do a fresh make
>>>>         install. Does that resolve the problem?
>>>>
>>>>         On Mon, Mar 14, 2011 at 2:55 PM, Bastil2001 at yahoo.de
>>>>         <mailto:Bastil2001 at yahoo.de> <Bastil2001 at yahoo.de
>>>>         <mailto:Bastil2001 at yahoo.de>> wrote:
>>>>
>>>>             Hi all,
>>>>
>>>>             I have build the 3.10 source from paraview.org
>>>>             <http://paraview.org> without any plroblems.
>>>>             However, I can run paraview only from the build
>>>>             directory. After a
>>>>             successuful "make install" I get:
>>>>
>>>>              /opt/paraview/3.10.0/lib/paraview-3.10/paraview:
>>>>             symbol lookup error:
>>>>             /opt/paraview/3.10.0/lib/paraview-3.10/libQtXmlPatterns.so.4:
>>>>             undefined symbol: _ZNK21QNetworkAccessManager10metaObjectEv
>>>>
>>>>
>>>>
>>>>             I use QT 4.6.2 which is not my system QT. All paths in
>>>>             ccmake 2.8.3
>>>>             point to this QT. Ideas?
>>>>
>>>>             Thanks Bastian
>>>>             _______________________________________________
>>>>             Powered by www.kitware.com <http://www.kitware.com>
>>>>
>>>>             Visit other Kitware open-source projects at
>>>>             http://www.kitware.com/opensource/opensource.html
>>>>
>>>>             Please keep messages on-topic and check the ParaView
>>>>             Wiki at: http://paraview.org/Wiki/ParaView
>>>>
>>>>             Follow this link to subscribe/unsubscribe:
>>>>             http://www.paraview.org/mailman/listinfo/paraview
>>>>
>>>>
>>>>
>>>>         _______________________________________________
>>>>         Powered by www.kitware.com <http://www.kitware.com>
>>>>
>>>>         Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html
>>>>
>>>>         Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView
>>>>
>>>>         Follow this link to subscribe/unsubscribe:
>>>>         http://www.paraview.org/mailman/listinfo/paraview
>>>
>>>
>>>
>>>     _______________________________________________
>>>     Powered by www.kitware.com <http://www.kitware.com>
>>>
>>>     Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html
>>>
>>>     Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView
>>>
>>>     Follow this link to subscribe/unsubscribe:
>>>     http://www.paraview.org/mailman/listinfo/paraview
>>
>>
>>     _______________________________________________
>>     Powered by www.kitware.com <http://www.kitware.com>
>>
>>     Visit other Kitware open-source projects at
>>     http://www.kitware.com/opensource/opensource.html
>>
>>     Please keep messages on-topic and check the ParaView Wiki at:
>>     http://paraview.org/Wiki/ParaView
>>
>>     Follow this link to subscribe/unsubscribe:
>>     http://www.paraview.org/mailman/listinfo/paraview
>>
>>
>>
>>
>> -- 
>> Robert Maynard
>>
>>
>> _______________________________________________
>> Powered by www.kitware.com
>>
>> Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html
>>
>> Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView
>>
>> Follow this link to subscribe/unsubscribe:
>> http://www.paraview.org/mailman/listinfo/paraview
>

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://www.paraview.org/pipermail/paraview/attachments/20110317/13b60eef/attachment-0001.htm>