[Paraview] plugin for 3D Delaunay

[Stefan Murphy]

Sorry, nevermind the last. mingw32-make seems to be doing something,
if that doesn't work I will go the VisualStudio route. Thanks.



On Feb 19, 2008 2:04 PM, Stefan Murphy <stefan.murphy at dal.ca> wrote:
> Is it possible to build with MinGW instead of VS? I was successful in
> generating a mingw Makefile with CMake, however I'm not sure what
> command to use to compile. mingw-make and make are not recognized.
>
>
>
>
> On Feb 19, 2008 1:38 PM, Mike Jackson <imikejackson at gmail.com> wrote:
> > Not sure since I always build from source. Point is that you need to
> > have BOTH Qt and ParaView built with the SAME compiler. Period.
> >
> > So.. download the source code version of Qt.
> > If you want to use Qt versions newer than 4.2.3 with ParaView you
> > will need to edit a line in a CmakeLists.txt file that checks for
> > that version.
> >
> > Then build Qt with VS 9
> > Install Qt
> > Build PV 3.x
> >
> > Mike
> >
> >
> > On Feb 19, 2008, at 12:29 PM, Stefan Murphy wrote:
> >
> > > I was assuming that the qt-win-opensource-4.3.3-mingw.exe file was a
> > > compiled package. I am going to try Qt4.2.3 to see if there is any
> > > difference.
> > >
> > >
> > >
> > >
> > > On Feb 19, 2008 1:18 PM, Mike Jackson <imikejackson at gmail.com> wrote:
> > >> Not sure on windows but I don't think you can actually mix a MinGW Qt
> > >> with a Visual Studio 9 ParaView. All the code most probably has to be
> > >> from the same compiler.
> > >>
> > >> Also, in the CMakeSetup GUI, there should be an entry for
> > >> QT_QMAKE_EXECUTABLE. Edit the entry to point to your Qt 4 qmake
> > >> executable, C:\Qt\4.3.3\bin\qmake.
> > >>
> > >> You will probably have to recompile Qt with VS 9 first.
> > >>
> > >> Mike
> > >>
> > >>
> > >> On Feb 19, 2008, at 12:11 PM, Stefan Murphy wrote:
> > >>
> > >>> I have installed CMake, and Qt 4.3.3 from the file
> > >>> qt-win-opensource-4.3.3-mingw. MinGW was installed with Qt. I
> > >>> obtained
> > >>> the source code for ParaView3.2.1.
> > >>>
> > >>> When I try to run CMake for Visual Studio 9, 2008 it says that Qt is
> > >>> not found, specifically asking me to check the QT_QMAKE_EXECUTABLE
> > >>> variable. I set this to C:\Qt\4.3.3\bin, but I get the same error.
> > >>>
> > >>> Is there anything else I have to do with Qt? I ran "configure
> > >>> -platform win32-g++" and added C:\Qt\4.3.3\bin to PATH and still get
> > >>> the same error.
> > >>>
> > >>>
> > >>> Stefan
> > >>>
> > >>>
> > >>>
> > >>> On Feb 18, 2008 6:24 PM, Jean Favre <jfavre at cscs.ch> wrote:
> > >>>> On 18, Feb 2008 10:48 PM, Stefan Murphy <stefan.murphy at dal.ca>
> > >>>> wrote:
> > >>>>
> > >>>>> Jean,
> > >>>>>
> > >>>>> I've been trying to compile your plugin with CMake, but I am
> > >>>>> getting
> > >>>>> the error:
> > >>>>>
> > >>>>> "CMake Error: ParaView_DIR is not set. It must be set to the
> > >>>>> directory
> > >>>>> containing ParaViewConfig.cmake in order to use ParaView."
> > >>>>>
> > >>>>> I have never used CMake before - Do you have the compiled .dll
> > >>>>> or .so
> > >>>>> file for the plugin?
> > >>>>
> > >>>> the procedure documented on the Wiki assumes prior knowledge of
> > >>>> Cmake,
> > >>>> and assumes that you have compiled your own version of ParaView
> > >>>> from the
> > >>>> source code distribution.
> > >>>>
> > >>>> The error above comes up the first time you run cmake while its
> > >>>> internal
> > >>>> variables are not set. While using Cmake, you should put in the
> > >>>> path to
> > >>>> the directory where you have previoulsy build ParaView. After
> > >>>> that, the
> > >>>> configuration can complete, and the Makefile gets generated.
> > >>>>
> > >>>> Looks however, like you have never done any of this. First step,
> > >>>> check
> > >>>> the wiki, compile your own Paraview. Once done with that, you may
> > >>>> get to
> > >>>> the second step of adding pluggins.
> > >>>>
> > >>>> Jean
> > >>>>
> > >>>>
> > >>
> >
> > --
> > Mike Jackson   Senior Research Engineer
> > Innovative Management & Technology Services
> >
> >
> >
>