[Paraview] plume tracking-trajectory

[Mathieu Westphal]

Hello

You can use the filter ParticleToPathLines on the TableToPoints filter to
visualize the path of your particle.

Mathieu Westphal

On Tue, Jul 26, 2016 at 5:39 PM, Konstantinos Panagiotou <
panagiotou.konstantinos at ucy.ac.cy> wrote:

> I hope this time is ok
> the vtk file is the flow solution,the csv file is the particle data
>
> kostas
> ------------------------------
> *From: *"Mathieu Westphal" <mathieu.westphal at kitware.com>
> *To: *"Konstantinos Panagiotou" <panagiotou.konstantinos at ucy.ac.cy>
> *Cc: *"ParaView" <paraview at paraview.org>
> *Sent: *Wednesday, July 27, 2016 12:24:04 AM
>
> *Subject: *Re: [Paraview] plume tracking-trajectory
>
> I am unable to load your pvsm.
> Please provide all the data needed by your pvsm in order for me to load it.
>
> Mathieu Westphal
>
> On Tue, Jul 26, 2016 at 5:03 PM, Konstantinos Panagiotou <
> panagiotou.konstantinos at ucy.ac.cy> wrote:
>
>> hello
>> i have loaded the csv data and a vtk file,a cube basicly, in which the
>> flow solution is stored
>>
>> ------------------------------
>> *From: *"Mathieu Westphal" <mathieu.westphal at kitware.com>
>> *To: *"Konstantinos Panagiotou" <panagiotou.konstantinos at ucy.ac.cy>
>> *Cc: *"ParaView" <paraview at paraview.org>
>> *Sent: *Tuesday, July 26, 2016 11:53:41 PM
>>
>> *Subject: *Re: [Paraview] plume tracking-trajectory
>>
>> Your data does not seem to be correctly formated.
>> Can you send me an associated pvsm file ?
>>
>> Mathieu Westphal
>>
>> On Tue, Jul 26, 2016 at 4:08 PM, Konstantinos Panagiotou <
>> panagiotou.konstantinos at ucy.ac.cy> wrote:
>>
>>> Dear Mathieu,
>>> i have installed cmake and qt in order to use cmake command to convert
>>> to .vtp. However,i need to add some additional packages which i am not
>>> familiar with.
>>> So, instead of converting to .vtp, i am sending you in zip form two
>>> files with different formats, vtk and csv respectively, files which i have
>>> loaded to paraview and being able to animate them using glyph. they are few
>>> KB each, it is the minimum i could do in order to keep the example as
>>> simple as possible for possible extension later on.
>>> Sincerely,
>>> Kostas
>>>
>>> ------------------------------
>>> *From: *"Mathieu Westphal" <mathieu.westphal at kitware.com>
>>> *To: *"Konstantinos Panagiotou" <panagiotou.konstantinos at ucy.ac.cy>,
>>> "ParaView" <paraview at paraview.org>
>>> *Sent: *Tuesday, July 26, 2016 8:06:16 PM
>>>
>>> *Subject: *Re: [Paraview] plume tracking-trajectory
>>>
>>> Please keep the ml in the loop so everyone can follow this.
>>>
>>> Please open you csv data, save it as a .vtp file and send it to me (if
>>> it's not too big)
>>>
>>> Regards,
>>>
>>> Mathieu Westphal
>>>
>>> On Tue, Jul 26, 2016 at 12:55 PM, Konstantinos Panagiotou <
>>> panagiotou.konstantinos at ucy.ac.cy> wrote:
>>>
>>>> Hello Mathieu,
>>>> i have applied the Temporal ParticlePath filter,however i havent seen
>>>> any change. I mean, when i apply glyph to the input data, i can activate
>>>> this filter and apply it to the input data,either vtk or csv point data.
>>>> However, i havent managed yet to see trajectories of the particles,
>>>> only the position of the particle or particles at a specific time step.I
>>>> have searched and I have seen in other posts in the forum referring to the
>>>> same issue, that the operation interface of the newest vesrion of paraview
>>>> is different than the previous ones for the specific function. Can you
>>>> guide me pls if you can? :)
>>>>
>>>> Thanks again,
>>>> Kostas
>>>> ------------------------------
>>>> *From: *"Mathieu Westphal" <mathieu.westphal at kitware.com>
>>>> *To: *"Konstantinos Panagiotou" <panagiotou.konstantinos at ucy.ac.cy>
>>>> *Cc: *"ParaView" <paraview at paraview.org>
>>>> *Sent: *Thursday, July 21, 2016 6:16:27 PM
>>>> *Subject: *Re: [Paraview] plume tracking-trajectory
>>>>
>>>>
>>>> Hello
>>>>
>>>> You should have a look to ParticlePath filter.
>>>>
>>>> Regards
>>>>
>>>> Mathieu Westphal
>>>>
>>>> On Thu, Jul 21, 2016 at 10:38 AM, Konstantinos Panagiotou <
>>>> panagiotou.konstantinos at ucy.ac.cy> wrote:
>>>>
>>>>> Hi,
>>>>> i am having a problem on plotting the trajectory of a single particle
>>>>> at the top of a flow solution. Particularly, i have a csv file, which is
>>>>> named text0000.csv,inside which i have 4 columns, x,y,z,t.in
>>>>> addition, i have additional files text0001.csv,text0002.csv etc, with one
>>>>> row each( variables' values at each time step)
>>>>> When i load them to the paraview project,i have no problem on
>>>>> performing the animation.However, i also want to have particle's trajectory
>>>>> while it evolves, that is,having lines connecting the updated points with
>>>>> the previous ones. But i havent managed to do that yet. I have installed a
>>>>> paraview version 5.0.1. pls help me,what i should do?
>>>>> _______________________________________________
>>>>> Powered by www.kitware.com
>>>>>
>>>>> Visit other Kitware open-source projects at
>>>>> http://www.kitware.com/opensource/opensource.html
>>>>>
>>>>> Please keep messages on-topic and check the ParaView Wiki at:
>>>>> http://paraview.org/Wiki/ParaView
>>>>>
>>>>> Search the list archives at: http://markmail.org/search/?q=ParaView
>>>>>
>>>>> Follow this link to subscribe/unsubscribe:
>>>>> http://public.kitware.com/mailman/listinfo/paraview
>>>>>
>>>>
>>>>
>>>>
>>>
>>>
>>
>>
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://public.kitware.com/pipermail/paraview/attachments/20160726/11aeb19d/attachment.html>