[Paraview] Import of .PLY fails in Paraview 5.1

[stephaneンドング メファネ]

Hello,

I do not think it is a size problem, as i tried also very small files.
Also, Sujin Philip managed to open the sample file I sent him without any
problem.

Stephane

川崎工場
火力タービン部 計画設計課
ンドング-メファネ ステファン
工学博士

富士電機株式会社
〒210-9530川崎市川崎区田辺新田1-1
TEL 044-329-2155 FAX 044-329-2394

On Fri, Jul 15, 2016 at 5:57 AM, Cory Quammen <cory.quammen at kitware.com>
wrote:

> Hmm, I don't see anything unusual with these settings files.
>
> Is your PLY file unusually large by chance?
>
> Thanks,
> Cory
>
> On Thu, Jul 7, 2016 at 9:46 PM, stephaneンドング メファネ
> <stephane at fujielectric.com> wrote:
> > Hello Cory,
> >
> > Paraview is still crashing if I start it normally and try to load a .PLY
> > (even after deleting the settings configuration files, so I am not so
> sure
> > the problem is coming from the config files....I don't know...).  I am
> > sending the original config files.
> >
> > Stephane
> >
> >
> > 川崎工場
> > 火力タービン部 計画設計課
> > ンドング-メファネ ステファン
> > 工学博士
> >
> > 富士電機株式会社
> > 〒210-9530川崎市川崎区田辺新田1-1
> > TEL 044-329-2155 FAX 044-329-2394
> >
> > On Fri, Jul 8, 2016 at 4:14 AM, Cory Quammen <cory.quammen at kitware.com>
> > wrote:
> >>
> >> Hi Sujin,
> >>
> >> Thanks for following up.
> >>
> >> Stephane,
> >>
> >> Could I get the settings configuration files in effect when you saw the
> >> PLY reader problem to try to figure out which settings caused this
> problem?
> >>
> >> Thanks,
> >> Cory
> >>
> >> On Thu, Jul 7, 2016 at 3:01 PM, Sujin Philip <sujin.philip at kitware.com>
> >> wrote:
> >>>
> >>> Hi Cory,
> >>>
> >>> We looked into this. The problem was not with the dataset but with the
> >>> paraview settings files ("paraview -dr" runs without issues).
> >>>
> >>> Thanks
> >>> Sujin
> >>>
> >>>
> >>> On Thu, Jul 7, 2016 at 1:59 PM, Cory Quammen <cory.quammen at kitware.com
> >
> >>> wrote:
> >>>>
> >>>> Hi,
> >>>>
> >>>> I can't reproduce this. Do you have an example PLY file you can share
> >>>> (directly with me if you wish) to try to reproduce the error?
> >>>>
> >>>> Thanks,
> >>>> Cory
> >>>>
> >>>> Th
> >>>>
> >>>> On Tue, Jun 28, 2016 at 4:24 AM, stephaneンドング メファネ
> >>>> <stephane at fujielectric.com> wrote:
> >>>>>
> >>>>> Hello,
> >>>>>
> >>>>> Paraview crashes everytime I try to import a point cloud (.PLY)
> >>>>> file.The same problem occurs when it is a .PLY file exported from
> Paraview.
> >>>>> Any idea on how to solve that problem?
> >>>>>
> >>>>> Ndong-Mefane Stephane, Dr.Eng
> >>>>> Basic Design Sec.
> >>>>> Steam Turbine Dept.
> >>>>> Kawasaki Factory
> >>>>>
> >>>>> Fuji Electric Co., Ltd
> >>>>> 1-1, Tanabeshinden, Kawasaki-ku,
> >>>>> Kawasaki-city 210-9530, Japan
> >>>>> Phone: +81-44-329-2155
> >>>>> Fax: +81-44-329-2394
> >>>>>
> >>>>>
> >>>>> _______________________________________________
> >>>>> Powered by www.kitware.com
> >>>>>
> >>>>> Visit other Kitware open-source projects at
> >>>>> http://www.kitware.com/opensource/opensource.html
> >>>>>
> >>>>> Please keep messages on-topic and check the ParaView Wiki at:
> >>>>> http://paraview.org/Wiki/ParaView
> >>>>>
> >>>>> Search the list archives at: http://markmail.org/search/?q=ParaView
> >>>>>
> >>>>> Follow this link to subscribe/unsubscribe:
> >>>>> http://public.kitware.com/mailman/listinfo/paraview
> >>>>>
> >>>>
> >>>>
> >>>>
> >>>> --
> >>>> Cory Quammen
> >>>> R&D Engineer
> >>>> Kitware, Inc.
> >>>>
> >>>> _______________________________________________
> >>>> Powered by www.kitware.com
> >>>>
> >>>> Visit other Kitware open-source projects at
> >>>> http://www.kitware.com/opensource/opensource.html
> >>>>
> >>>> Please keep messages on-topic and check the ParaView Wiki at:
> >>>> http://paraview.org/Wiki/ParaView
> >>>>
> >>>> Search the list archives at: http://markmail.org/search/?q=ParaView
> >>>>
> >>>> Follow this link to subscribe/unsubscribe:
> >>>> http://public.kitware.com/mailman/listinfo/paraview
> >>>>
> >>>
> >>
> >>
> >>
> >> --
> >> Cory Quammen
> >> R&D Engineer
> >> Kitware, Inc.
> >
> >
>
>
>
> --
> Cory Quammen
> R&D Engineer
> Kitware, Inc.
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://public.kitware.com/pipermail/paraview/attachments/20160716/49b52a59/attachment.html>